BENTLY NEVADA 330104-00-10-10-02-CN 3300 XL FAMILY 8MM PROXIMITY PROBE

Technical parameter

No thread length option (00) : 0 mm

Total housing length option (10) : 100 mm

Total Length options (10) : 1.0 m (3.3 ft)

Connector and Cable type options (02) : Small coaxial ClickLoc connector, standard cable

Certification Options (CN) : Certification for specific countries or regions (see the CN Certification Quick Reference Guide)

Physical parameters:

Probe diameter: 8 mm

Probe tip material: polyphenylene sulfide (PPS)

Probe housing material: AISI 303 or 304 stainless steel

Cable material: oil - and corrosion-resistant insulation material

Weight: Approx. 0.3kg (without cable)

Measurement performance:

Measuring range: 0-8 mm (0-0.315 in)

Linear range: approximately 2 mm (80 mils)

Accuracy: ± 0.01mm (±0.0004 in)

Repeatability: ± 0.005mm

Minimum target size: 15.2 mm (0.6 in) Diameter (flat target)

Frequency response: 0-10 kHz (depending on system configuration)

Environmental parameters:

Operating temperature range:

Probe: -35°C to +177°C

Cables and connectors: -35°C to +120°C

Protection level:

Probe: IP67 (oil and corrosion resistance)

Connector: IP65 (to be installed correctly)

Pressure resistance: The probe uses a Viton® O-ring to seal the pressure difference between the probe tip and the housing, but is not pressure-tested before delivery. For pressure seal testing, contact custom design department.

Electrical parameters:

Power supply: Used with the Bently Nevada 3300 XL series monitoring system

Output signal: Voltage signal (usually compatible with monitoring system)

Compatible systems: Bently Nevada 3500 Series or other monitoring systems that support the 3300 XL probe

Compliance:

API 670 compliant (Mechanical Vibration and Displacement monitoring)

Certification: CN (for country-specific or regional certification, refer to Bently Nevada's CN Certification Quick Reference Guide and on-site notification letter)

Feature

Non-contact vibration measurement:

The shaft vibration of rotating machinery is measured close to the probe, providing high precision data.

Support radial vibration, axial displacement and speed measurement.

Shaft position monitoring:

The relative position change of the shaft is detected for monitoring bearing wear, shaft alignment and other problems.

Mechanical condition monitoring:

The Bently Nevada monitoring system provides real-time data for machine condition analysis and fault diagnosis.

Supports early fault detection, such as unbalance, misalignment, and loosening.

Environmental adaptability:

Designed for harsh industrial environments, oil and corrosion resistant, suitable for high temperature and high pressure scenarios.

Equipped with ClickLoc connectors to prevent loosening and signal interruptions.

Meet country-specific certification requirements for scenarios that require special compliance.

Easy to install and maintain:

The probe and cable are modular in design for easy installation and replacement.

ClickLoc connectors support fast connections and reduce installation time.

Data acquisition and analysis:

The output signal can be integrated with the monitoring system to support real-time data acquisition, recording and analysis.

Support predictive maintenance to reduce unplanned downtime.

Application scenario

Oil and gas:

Monitor the vibration and shaft position of compressors, pumps and turbines.

Suitable for offshore drilling platforms, refineries and other scenarios that require specific certification.

Meet compliance requirements for specific countries or regions.

Power industry:

Monitor the operation of generator sets (such as steam turbines, gas turbines, water turbines).

Detect bearing failure, rotor imbalance and other problems.

Suitable for power facilities that require specific certification.

Chemical Industry:

Monitor the vibration of centrifugal pumps, agitators, fans and other equipment.

Ensure reliable operation of equipment under high temperature and high pressure environment.

Meet the certification requirements of specific countries or regions.

Steel and Manufacturing:

Monitor vibration and displacement of rolling mill, motor and gearbox.

Improve equipment utilization and reduce production disruptions.

Suitable for manufacturing environments that require specific compliance.

Paper and Food Processing:

Monitor the operating status of conveyor drive system, fan and pump.

Ensure the continuity and stability of the production line.

Suitable for processing environments that require specific certification.

Marine and Marine Engineering:

Monitoring the vibration of the ship's propulsion system and generators.

Adapted to the corrosive and high humidity conditions of the Marine environment.

Meet the certification requirements of specific countries or regions.

Advantage Products:

All items are Distributor Ready-stock Genuine Brand-new Supplying, please inform us if the other conditions are needed, Used, Open-box, Refurbished, etc.

Many Available just wait for you, feel free to ask to get better deal!!!

Bou L(Sales Manager)            

Tel:+86-175 5077 6091                                                                                              

E-mail:[email protected]       

Tina(Sales Specialist)       

Tel:+86-131 2336 8748                                                                                                            

E-mail:[email protected]     

Elaine(Sales Specialist)       

Tel:+86-185 5982 5148                                                                                                         

E-mail:[email protected]